Replacement tent parts: poles, zips, groundsheets and more

On a canvas tent, the parts that wear out first are zips and sliders, guy ropes and runners, pegs and the groundsheet, followed by poles that get bent and panels damaged by sun or accidents. All of them can be replaced individually. To order the right part, send the tent model, approximate purchase date, photographs and measurements; operators should keep a small spares kit on site so a single failure never takes a tent out of service.

6 min read ยท Updated

Round canvas pavilion with a scalloped valance

Which canvas tent parts wear out first

A canvas tent is a set of components, and the canvas is usually the longest-lived of them. Slings, covers, liners, groundsheets, pole sections and peg sets are all available individually from us, so a structure never has to be retired because one part reached the end of its life. That is a principle on our craftsmanship page, and it is also simple economics for anyone running a site: a groundsheet replaced on time protects a tent worth many times its price.

Wear rates depend on use, climate and handling. A bell tent pitched twice a year for family camping and a glamping unit standing all season will wear very differently. Use this as a guide to what to watch rather than a schedule.

Common replacement parts on canvas tents
PartSigns it needs replacingNotes
Zip sliderZip closes then splits behind the sliderCheap and quick to replace; the zip itself is often fine
ZipMissing teeth, torn tape, slider will not runA sewing job; quote the length and gauge
Guy ropes and runnersFraying, glazing, cracked or slipping runnersReplace in sets so tension stays even
PegsBent, lost, rusted at the headKeep a spare set; match the type to your ground
Separate groundsheetPunctures, abrasion, cracking at foldsThe cheapest protection for the tent floor
Zip-in groundsheetSplits, worn corners, failed zipCan be replaced without replacing the tent
Poles and frame membersBends, kinks, damaged ends or jointsNever straighten and reuse a structural pole
Canvas panelLong tears, rot, brittle cloth from UVCut to the original pattern
Mesh, liners, storm skirtTears, mould, wear at ground levelReplaced individually

Replacement poles and frame members

Our bell tents use galvanised steel centre poles and A-poles; tipis use powder-coated steel; safari tents and cottages stand on hot-dip galvanised frames. A bent pole has been weakened at the bend and will fold there again under less load, so replace the section rather than straightening it. Measure the length and outside diameter, photograph the ends and any joint fittings, and tell us the tent model. For framed tents, the installation drawing supplied with the structure identifies each member, which makes ordering much simpler, so keep it with your site records.

Carry poles in a pole bag with a reinforced base. Most pole damage happens in transport and storage, not in the pitched tent.

Replacing tent zips and sliders

Zips are tested at the factory, but daily use on a guest tent puts years of camping into one season. Replace a worn slider first: it is the usual cause of a zip that splits. A full zip replacement means unpicking and re-sewing, which we or a local sail-maker can do. When ordering, give the length of the zip and photograph the slider, which usually carries a size number. Keep zips brushed clean and lubricated with a product made for outdoor zips, and do not force a door zip against a taut wall.

Replacement groundsheets and footprints

Our bell tents come with a 540 gsm PVC zip-in groundsheet (610 gsm on the 6 m). Underneath it, a separate footprint takes the abrasion, puncture and ground damp. The Tent Groundsheet 4M and 5M are cut fractionally inside the tent line so rain running off the walls does not land on them. For other sizes, or under a deck, the Ground Sheet Tarpaulin is a consumable worth replacing whenever it is worn.

Guy ropes, pegs and small hardware

Guy ropes fray where they run through runners and over eyelets, and they glaze and stiffen with UV. Replace them in full sets so tension stays even round the tent. Pegs get bent in stony ground and lost in long grass; buy a spare set and keep them in a lined peg and stake bag so wet steel stays off the canvas. Small hardware such as eyelets, runners and storm-flap toggles is cheap to stock and costly to be without on a busy weekend.

Replacement canvas panels, liners, mesh and storm skirts

Canvas panels are cut from our own patterns, so a replacement can be made to fit the original rather than adapted. The storm skirt and the lowest band of wall take the most wear, from soil, damp grass and strimmers, and on bell tents in particular they are often the first canvas to need attention. Mesh panels tear where they are pushed or caught, and liners pick up mould if a tent is kept closed in humid weather.

When the outer skin of a framed tent or yurt is tired all over, ask for a full replacement skin on the existing frame. The frame is designed to outlive several skins, and a new cover is a fraction of the cost of a new structure. For cut-to-size repairs of your own, treated tent canvas and ripstop poly-cotton are sold by the metre.

How to order the right replacement part

The faster we can identify the part, the faster it ships. Send these through our contact page or to info@canvashome.com.

  • The tent model or SKU, and roughly when and from whom it was bought.
  • Clear photographs of the part, the damage and where it fits on the tent.
  • Measurements: pole length and diameter, zip length, panel dimensions, groundsheet diameter.
  • Quantity, and whether you want spares for other units at the same time.
  • Your delivery country, since freight and duties change the landed cost of small parts as much as large ones.

What spare parts a glamping site should keep

A site with several identical units should hold spares on site. As a rule of thumb, keep enough to fix any single failure on any one tent the same day: a spare set of guy ropes and runners, a dozen pegs, two zip sliders of each size, a centre pole or the most vulnerable frame member, a groundsheet, a patch kit with matching canvas and polyester thread, and a can of proofer. Ordering identical structures, as in a five-tent resort package, makes this far easier, because one set of spares covers every unit.

Questions buyers ask

Can I buy replacement poles for a bell tent?

Yes. Centre poles and A-poles are sold individually. Send the tent size and pole measurements so we can match diameter and fittings.

Can I replace a zip-in groundsheet without replacing the tent?

Yes. Groundsheets are a separate component and can be ordered on their own for our bell tents.

My tent zip keeps splitting. Do I need a new zip?

Usually not. A zip that splits behind the slider normally has a worn slider, which is a cheap and quick replacement.

Do you supply parts for tents you did not make?

We can supply canvas by the metre, groundsheets, bags and general hardware. Poles and panels are best matched to tents made from our own patterns.

How long does it take to get spare parts?

Stock items ship quickly; made-to-measure panels and zips take longer. Shipping time and cost depend on your country, so ask for a quote with delivery.

Pieces in this guide

Read next

Request a quote