Electricity and lighting in tented rooms

Power reaches a tented room by an underground cable to a small protected distribution point at each unit, then along the tent frame to outdoor-rated fittings that never touch the canvas. Lighting should be LED, warm in colour and layered, with battery lanterns as backup. All fixed wiring must be designed, installed and certified by a licensed local electrician to the codes where you build. This guide covers good practice only, and compliance is for your electrician to confirm.

6 min read ยท Updated

White canvas resort tents with palms and a parasol

Start with a licensed electrician and the local code

Electricity in a canvas structure is ordinary electrical work in a harder environment: damp, movement, metal frames, guests who leave hair dryers on the floor. Every country has its own wiring rules and many treat temporary or tented accommodation as a special case. Bring a licensed local electrician in at the design stage, before you order tents, so cable entries and fixing points are built into the structure and not cut in later.

What we can do from the tent side is tell your electrician where the frame members run, where cables can enter, and which parts of the structure can carry a fitting. Ask us for the installation drawing with your quote.

Getting power to each tent

On a permanent site the usual arrangement is an underground supply from a main board to each unit, in ducting, with a small distribution point at the tent protected by circuit breakers and residual-current devices (called RCDs in the UK, GFCIs in North America). Your electrician will decide on cable type, burial depth, earthing and whether the metal frame needs bonding.

The cable should come up through a sleeve in the deck, not through the canvas and not across the floor. Our Command Post Tent uses sealed cable entry ports for exactly this reason, and the same principle applies to a resort tent: one defined, weatherproof point of entry, with a drip loop so water running down the cable falls away before the gland.

How much power a tented room uses

A tented room uses very little power for light and a great deal for heat or cooling. The figures below are typical ranges for common appliances, enough to show the order of magnitude your electrician will work with; they are not a design calculation.

Typical appliance loads in a tented room (indicative ranges; check the actual appliances you buy).
UseTypical loadNote
LED lighting for the whole tentTens of wattsBarely registers on the load
Phone and laptop chargingTens of wattsProvide USB points by the bed
Ceiling or pedestal fanRoughly 30 to 100 WThe cheapest comfort upgrade
Kettle or coffee machineRoughly 1 to 3 kWShort but heavy draw
Hair dryerRoughly 1 to 2 kWGuests will bring their own
Split air conditionerOften 1 to 3 kW runningUsually needs its own circuit
Electric water heaterOften 2 to 4 kW or moreUsually needs its own circuit

Running cables inside a canvas tent

Canvas moves, sags slightly when wet and can chafe anything pressed against it. Cables therefore run along the frame, never across the fabric, fixed with clips or in conduit. Framed safari and Swiss cottage tents make this straightforward: the galvanised frame gives a ridge, eaves and uprights to work along. Bell tents and tipis have only a centre pole, so fixed wiring is usually limited to a conduit up the pole and a floor box at its base.

  • Use fittings with an ingress protection (IP) rating suited to damp locations; your electrician will specify the level.
  • Keep every light fitting clear of the canvas. Even LEDs get warm at the driver, and halogen or incandescent lamps should not be used near fabric at all.
  • Put sockets on posts or furniture at worktop height, not on the floor where cleaning water and spilled drinks reach them.
  • Label the distribution point and give housekeeping a simple isolation procedure.

Choosing lighting for a canvas tent

Canvas glows when lit. From outside, a lit tent at dusk is the photograph most properties use to sell; from inside, harsh light bounces off pale cloth and flattens the room. Warm colour temperatures of roughly 2200 to 2700 K look right on canvas and make the interior feel like evening instead of an office.

Layer the light: a low central fitting or pendant from the ridge for general light, reading lights at the bed, and one or two lamps on tables. Our Brass Camp Lantern puts a 2200 K dimmable LED and a USB-C cell inside a spun brass body, and the Canvas-Shade Table Lamp does the same job on a bedside table. Neither needs a socket, so they double as the backup when the power fails, which on a rural site it will.

Outside, keep path lighting low and shielded so it lights the ground and not the neighbours. The String Light Set runs ten metres of IP44 cord from a battery pack, enough to ring a bell tent veranda without any fixed wiring.

Smoke alarms, emergency lighting and electrical checks

A battery smoke alarm in every tent costs very little, and many fire authorities and insurers will expect one; ask yours what they require, including whether alarms must be interlinked or mains-powered. If any heater in the tent burns fuel, add a carbon monoxide alarm as well. Low-level emergency or battery lighting along the paths lets guests find their way out when the supply trips at night.

Build inspection into the maintenance calendar. Residual-current devices should be tested at the interval your electrician recommends, cable entries checked after every storm, and anything under the deck looked at for rodent damage, which is a common cause of faults on rural sites. Our guide to keeping pests out of tents covers the under-deck side.

Off-grid power for glamping tents: solar and batteries

Plenty of good sites are nowhere near a grid connection. Solar panels feeding a battery bank will comfortably run LED lighting, fans and charging for a tent. They will not cheaply run air conditioning, electric showers or kettles for every room at once, which is why off-grid camps often heat water with gas or solar thermal and accept fans in place of AC.

A central solar array and battery room, cabled to each tent, is easier to maintain than a panel on every roof and keeps panels off the canvas. Installation should still be by a licensed electrician; battery systems carry their own fire and ventilation requirements.

Questions buyers ask

Is it safe to have electricity in a canvas tent?

It can be, if a licensed electrician designs and installs it to local rules, with residual-current protection, outdoor-rated fittings and cables kept on the frame and off the fabric. Treat it as a damp location throughout.

Can I run an extension lead to a glamping tent?

For a permanent guest unit, no. Use a buried supply in ducting to a protected distribution point at the tent. Extension leads across grass are a trip and shock hazard and are not a substitute for fixed wiring.

What colour temperature is best for tent lighting?

Warm white, roughly 2200 to 2700 K. It flatters canvas and timber and keeps the interior feeling like a room at night.

Can glamping tents run on solar power?

Yes, for lighting, fans and charging. Heating, cooling and electric hot water need much larger systems, so off-grid sites usually use gas or solar thermal for those.

Do your tents come pre-wired?

No. We supply the tent with cable entry and fixing details so your local electrician can wire it to your local code.

Pieces in this guide

Read next

Request a quote